What are the different types of retaining clips?

The 4 key retaining rings types are tapered section, constant section, spiral, and circular push‑on.

What are retention clips?

Originally developed to reduce assembly time, they provide much greater retention than previously used metal clips. The high-retention fasteners have now expanded for use on sunshades and other interior components. Look around your car and you are likely to see one of these clips.

What are those circle clips called?

Circlips
A ring clip is another name for an E-Type External Circlip, which is often referred to as an E-ring or an E-clip. Circlips are fasteners that fit into radial grooves in shafts and holes — and are sprung so they remain securely in place.

How do you install a retaining clip?

How to Install a Snap Ring

1. Put on a pair a pair of safety glasses.
2. Insert the tips of a needle-nose or circlip pliers into the holes at the end of the snap ring.
3. Open the pliers so the arms of the snap ring are pulled back and the loop of the ring widens.
4. Slip the expanded snap ring over the groove of the wheel.

What is the difference between a snap ring and a retaining ring?

Retaining rings — also known as snap rings or circlips — are metal fasteners installed into a groove on a shaft, or in a housing or bore to retain an assembly. The devices keep parts in place using a compact, lightweight design that requires fewer machining operations than other fastening techniques.

How do I choose a circlip?

It is always important to choose the right circlip sizes for the job at hand. The retaining ring must be suitable to fit inside the shaft where it will be installed (internal circlips) or should fit snugly around the outside of the housing (external circlips).

What is a spring clip?

Definition of spring clip 1 : a U-shaped piece of metal used to fasten a leaf spring to the axle of a vehicle. 2 : a small clip working with a spring (as for electrical terminal connections)

Where are snap rings used?

Snap rings are a great way to rapidly mount your bearings and have them adequately located axially in your application. They are often used in external applications to secure parts on grooved shafts, pins, or studs. External circlips are designed to ensure a tight fit into a grove around the outside of a shaft or rod.

Why is it called a Jesus clip?

The term “Jesus clip” comes from the propensity of the clip’s spring action to launch the clip at a high velocity when removing or installing, leading to remarks such as, “Oh Jesus, where did it go?”

What is an Eclip?

E-clips—also known as E-rings—are three pronged, stamped clips that fit into machined grooves of smaller diameter tubes and shafts.

Can you reuse snap rings?

They hold gears, cams and pulleys on shafts, and they keep bearings, valves, nozzles and locks inside housings. Also known as snap rings, these fasteners are removable and reusable.

What can I use instead of a retaining ring?

COTTER PIN AND WASHER. You could hold the shaft to the brace by drilling a hole through it, installing a washer and fastening the system with a cotter pin. Or, you could simply machine a groove onto the shaft and install a retaining ring (example on right). It creates a “shoulder” that retains the component or assembly …

Can I use e clip instead of snap ring?

We use e clips over snap rings because for snap rings you need to turn down the shaft to a circle. E clips don’t require the circular shaft and can easily be pressed into the machined groove (no tool is needed).

What kind of circlips are there?

There are two types of circlip; internal and external. The most commonly used circlip for most applications is a simple spring steel circlip, or plain wire ring. The clips can be known as wrist pin retainers, wrist pin clips, or gudgeon pin clips, when used to retain piston wrist pins or gudgeon pins.

What is a duck clip?

Duckbill clips are clips which are used to hold hair while it is styled, cut, or dyed. These clips do look vaguely like the beaks of ducks.

Is a snap ring the same as a retaining ring?

Snap rings are commonly referred to as retaining rings, circlips (circle and clip), or c-clips. They can have a stamped, tapered design. The rings are a type of fastener consisting of a metal ring with open ends which can be “snapped” into place.

Do helicopters still have the Jesus nut?

Now a lot of modern helicopters don’t have a Jesus nut. There are many other different methods of fixing the main rotor to the mast. However, the name is not going to disappear, because people are already using it for other crucial components of other mechanisms.

What are C-clips used for?

Usage: Circlips, C-clips, Jesus clips or Seeger rings are essentially a type of fasteners, which are most commonly used to keep dowel pins in place, in machine grooves. Circlips allow rotation but restrict the lateral movement of shafts and dowel pins.

What do circlips do?

Circlips are small, semi-flexible metal rings. They are a type of fastener and are also known as C-clips, Seeger rings, snap rings or Jesus clips. They’re most commonly used in machine grooves, where their key job is to hold dowel pins securely in place.

What does a snap ring look like?

A snap ring is a strong, thin, C-shaped metallic ring that works as a retaining fastener on shafts and inside circular bores to retain assembly parts. However, unlike a nut or bolt that threads onto a piece, a snap ring or C-clip snaps into a circular groove inside a bore housing or on the shaft.

What can I use instead of a circlip?

Another popular method of pin retention is the use of spiral locks. These are basically a helical design, being a spring of just less than two coils and made from flat material. They act in the same way as a circlip but are renowned for being very difficult to remove.

What is an X washer retaining ring?

Also known as X- washers, place these rings into the groove and squeeze tight with pliers to form a 360° closure. Often used with small engines, heavy equipment, and power transmission, these external retaining rings have speared ends to help you install and remove them.

How do you use a constant section retaining ring?

Also known as X- washers, place these rings into the groove and squeeze tight with pliers to form a 360° closure. Also known as constant-section rings, these rings have open ends and a profile that does not taper like other external retaining rings. Use them with linear bearings on support rail shafts.

What is an external retaining ring on a car?

Often used with small engines, heavy equipment, and power transmission, these external retaining rings have speared ends to help you install and remove them. Also known as X- washers, place these rings into the groove and squeeze tight with pliers to form a 360° closure.

What is an e style retaining ring?

Also known as reinforced E‐style rings. Also known as poodle rings, these thick rings have “ears” that form a large retaining surface to withstand stronger forces than other side-mount retaining rings. Also known as bowed E-style rings, these have a curved design that works like a spring, taking up play for a tight hold.