How do I refurbish my kitchen table?
How do I refurbish my kitchen table?
- Step 1: Clean the Surface. Use gentle soap and water to remove dirt and oils from the table’s existing finish.
- Step 2: Apply Stripper. If the table is painted or varnished, you’ll need to strip the surface.
- Step 3: Clean With Mineral Spirits.
- Step 4: Sand Table Surface.
- Step 5: Apply Stain.
- Step 6: Apply Finish.
How much does it cost to refinish the top of a table?
Cost to Refinish a Table. A basic table will range between $200 and $600 to refinish. The process is typically the same regardless of condition, and price changes only based on size. For any wooden table, the process involves stripping the old finish and applying a new final coat.
What kind of finish goes on a kitchen table?
Polyurethane varnish is the quickest and easiest way to finish a kitchen table. Most flow well when brushed on and leave few, if any, marks. Though it’s important to follow the manufacturer’s instructions carefully, properly finishing a kitchen table generally requires two to four coats of varnish.
How much does it cost to resurface a dining table?
It costs an average of $250 to refinish a table, with a typical range of $150–$400. The minimum cost to refinish a wood table is $80. The maximum cost is $700. Your project’s cost will largely depend on table size.
How do you tell if wood can be refinished?
Water Test. Pour a spoonful of water onto the floor. If it forms droplets that stay on the surface of the wood, the floor finish is still good. If the water is slowly absorbed into the wood, the finish is worn and needs to be restored.
Should I stain or paint my kitchen table?
For that reason, staining your kitchen tabletop is usually a better move than painting it–over time, a stained wood surface is going to hold up better than a painted surface will (and that goes for whatever kind of paint you use!)
What is the best polyurethane to use on a kitchen table?
Best for New Woodworkers-General Finishes Arm-R-Seal This is a tough product with a very smooth finish, and it is perfect for a dining table or a kitchen table. It dries hard with just 3 coats and is arguably the easiest can-based finish to apply. You can wipe it on, use a natural bristle brush, foam pad or spray.
Does refinishing antique reduce value?
Refinishing valuable American masterpieces can diminish the value, or painting over or removing hand-painted techniques can reduce the integrity of an antique. However, in general, cleaning and restoring old furniture can add value and help bring it back to life.
How many coats of polyurethane should you put on a kitchen table?
The polyurethane coat requires at least three coats to give the table a perfect finish. But you can put more layers to make the table look glossy and shiny. Make sure that you give time to each coat to be dried up properly.
What you need to refinish a table?
Shop for supplies
- All-purpose cleaning spray and a cloth or paper towels.
- 60-, 120-, and 360-grit sandpaper.
- A block sander or an orbit sander.
- A clean, dry tack cloth.
- Stain (or primer and paint)
- Paint and varnish remover (stripper)
- Putty knife.
Is it cheaper to refinish hardwood or replace?
Refinishing hardwood floors is more cost-effective than replacing them. On average, it costs about $2,000 to $7,000 to replace hardwood flooring (two to three times more than to refinish).
How many times can you refinish hardwood?
A solid hardwood plank at least 3/4 inches thick will likely need to be refinished four to six times during its total lifespan. It’s commonly accepted that you refinish every seven to ten years. Important note: some hardwood is only 1/4 inches thick. In this case, a refinish could strip away all traces of the floor.
How many coats of polyurethane should I put on a kitchen table?
- In most circumstances, you only need three coats of oil-based polyurethane.
- You need at least two coats of polyurethane on wood countertops.
- You should use at least three coats of polyurethane on a kitchen table.
- Read: Protective Coating For Painted Kitchen Cabinets.